Home > GRE Tunnel Tutorial

GRE Tunnel Tutorial

April 26th, 2018 Go to comments

GRE stands for Generic Routing Encapsulation, which is a very simple form of tunneling. With GRE we can easily create a virtual link between routers and allow them to be directly connected, even if they physically aren’t. Let’s have a look at the topology below:


Suppose R1 and R2 are routers at two far ends of our company. They are connected to two computers who want to communicate. Although R1 and R2 are not physically connected to each other but with GRE Tunnel, they appear to be! This is great when you have multiple end points and don’t care the path between them. The routing tables of two routers show that they are directly connected via GRE Tunnel.

How GRE Tunnel works

When the sending router decides to send a packet into the GRE Tunnel, it will “wrap” the whole packet into another IP packet with two headers: one is the GRE header (4 bytes) which uses to manage the tunnel itself. The other is called “Delivery header” (20 bytes) which includes the new source and destination IP addresses of two virtual interfaces of the tunnel (called tunnel interfaces). This process is called encapsulation.


In the example above when R1 receives an IP packet, it wraps the whole packet with a GRE header and a delivery header. The delivery header includes new source IP address of (the IP address of R1’s physical interface which is used to create tunnel) and new destination IP address of (the IP address of R2’s physical interface which is used to create tunnel).

It is important to note that the GRE tunnel does not encrypt the packet, only encapsulate it. If we want to encrypt the packet inside GRE Tunnel we must use IPSec but it is out of CCNA scope so we will not mention here.

When the GRE packet arrives at the other end of the tunnel (R2 in this case), the receiving router R2 needs to remove the GRE header and delivery header to get the original packet.

Unlike VPN which does not support multicast, GRE tunnel does support multicast so many popular routing protocols (like OSPF, EIGRP) can operate along with.

Note: The IP addresses of the two ends of GRE Tunnel ( & in this case) can be in the same subnet or different subnet (like over the Internet with public IP addresses), provided that two routers know how to reach each other’s tunnel IP address. For example in this case R1 must know how to reach and R2 must reach

Now you learned the basis of GRE Tunnel. It is important to show you the related GRE configuration of the example above. Suppose OSPF is used in our company.

R1 (GRE config only)
interface s0/0/0
ip address
interface tunnel0
ip address
tunnel mode gre ip //this command can be ignored
tunnel source s0/0
tunnel destination
router ospf 1
network area 0
R2 (GRE config only)
interface s0/0/0
ip address
interface tunnel1
ip address
tunnel source
tunnel destination
router ospf 1
network area 0

In the above R1 configuration, the command interface tunnel0 create the virtual tunnel 0 interface, which is called a tunnel interface. We can use any number. The tunnel numbers do not need to match on two routers so on R2 we can use “interface tunnel1” without any problem.

The next line assigns the IP address for the tunnel interface: The IP addresses of two tunnel interfaces must be in the same subnet ( on R1 & on R2 in this case).

The command tunnel mode gre ip is in fact not necessary as this is the default setting. We just want to show you this command and let you know that we are configuring a traditional point-to-point GRE. There are other GRE modes like “tunnel mode gre multipoint” used in DMVPN or “tunnel mode gre ipv6” to encapsulate IPv4 packets in an IPv6 infrastructure.

Next we have to specify the tunnel source and tunnel destination with “tunnel source …” and “tunnel destination” commands. For “tunnel source” command, we can either specify the interface or the IP address of the interface. When we define the tunnel source and tunnel destination in the tunnel interface, the router will add these IP addresses to the GRE packet generated by the tunnel interface. At the receiving end, the router looks for the tunnel destination and decapsulates the packet, then forwards it to the specific tunnel interface.


Note: We can use loopback interface as the tunnel source or destination. Traffic will flow through the best physical path toward the tunnel destination.

One last note, GRE tunnels are stateless which means the tunnel endpoint does not keep any information about the state or availability of the remote tunnel endpoint. Therefore the local tunnel endpoint does not bring the line protocol of the GRE tunnel interface down if the remote tunnel endpoint is unreachable. For example, if R2 tunnel interface is brought down for some reason, R1 tunnel interface will remain in up state.

If you are interested in full config for GRE please read our GRE tunnel Lab to have detailed knowledge of how to configure GRE tunnel.

Comments (8) Comments
Comment pages
1 2 3 4084
  1. omercitak
    April 3rd, 2019

    Please i need the latest dumps for CCNA R&S 200-125, please send to my email fomercitak @ gmail dot com

    Thanks in advanced

  2. wiqaskhan
    April 7th, 2019

    if anyone have latest dumps of CCNA R&S 200-125 please forward to waqasmrd03atgmaildotcom.

  3. kingosed
    April 24th, 2019

    please I need to latest dump {email not allowed}

  4. jake
    May 2nd, 2019


    Is it the network IP address on ospf configuration on R2 should be network “” area 0?


  5. Learn and EARN
    May 14th, 2019

    You lazy folks need to stop asking for the dumps. Study and EARN your certs.

  6. Chris
    May 22nd, 2019


    If any one has latest CCNA R&S 200-125 please forward to {email not allowed}

  7. Chris
    May 22nd, 2019


    If any one has latest CCNA R&S 200-125 please forward to chrisraj0123atgmail.com

    Thanks in Advance

  8. Cihat
    May 23rd, 2019


    If any one has latest CCNA R&S 200-125 please forward to omercihatataa at gmail.com

Comment pages
1 2 3 4084
Add a Comment